Clear Epoxy resin, 3 x 3.78L

もっと見る

Clear Epoxy resin, 3 x 3.78L

在庫: 在庫あり

RE-001200-H
$359.85
CTM INDUSTRIAL, ECTR is a clear, industrial quality epoxy resin that is easy to use and that will keep its transparency over time.
概要

詳細

DESCRIPTION

ECTR is a solvent-free two-component epoxy coating with excellent physical properties in addition to appearance. This system has been approved by the Canadian Food Inspection Agency (CFIA).

KEY FEATURES

* Contains 100% solid materials (no VOC), allowing an interior application without harmful odours
* Dense surface resistant to bacteria, moisture and easy to clean
* Excellent adhesive properties, allowing application on different types of substrates
* Can be applied in several layers with excellent adhesion

SURFACE PREPARATION:

The surface to be coated must be well primed. Remove dust, laitance, grease, oil, dirt, curing surface agents, impregnating agents, wax, foreign matter, coatings and disintegrated substances by mechanical means such as blasting (BLASTRAC) or any other approved method. The compressive strength of the concrete must be at least 25 MPa (3625 psi) after 28 days and the tensile strength is at least 1.5 MPa (218 psi).

MIXING:

Mix the resin part (A) separately before pouring the hardener (Part B) according to the specified mixing ratio. Mix for at least 3 minutes at low speed (300 to 450 rpm). During mixing, scrape the walls and bottom of the container at least once with a trowel to obtain a homogeneous mixture. Since the pot life is limited, prepare the mixtures in order to avoid any loss

APPLICATION:

Apply the coating with a rubber squeegee and standardize it with a roller in order to obtain a uniform covering.

RESTRICTIONS:

* Minimum / maximum substrate temperature 10 °C / 30 °C (50 °F / 86 °F).
* Maximum relative humidity during application and curing: 85%.
* The temperature of the substrate must be 3 °C (5.5 °F) higher than the measured dew point.
* The moisture content of the substrate should be <4% when the coating is applied.
* Do not apply to porous surfaces where moisture transmission may occur during application.
* Avoid use outdoors on substrates at ground level.
* Protect from moisture, condensation and contact with water during the initial 24-hour curing period.
* The surface may discolour in areas exposed to regular ultraviolet light.
 
Mixing ratio by volume:    2 parts of A 1 part of B
Mixing ratio by weight:    100 A 41-48 B
Pot Life (454 g):    20 - 30 minutes
Waiting for the application of a 2nd coating:    8 - 12 hours
Coverage per gallon *
(8 mils thick):    200 ft2
Recommended Thickness:
Primer:    4 - 6 mils
Finish:    8 - 12 mils
Pedestrian Traffic:    12 - 24 hours
Normal traffic:    24 - 48 hours
Heavy equipment traffic:    > 48 hours
Storage:    12 months
Density (kg / L)
Part A    1.05 - 1.10 (clear)
Part B    0.9 - 1.00
Solids by Weight (%) (Both part A and B):    100
Solids by volume (%) (Both part A and B):    100

* Note that the coverage per gallon shown is calculated for flat surfaces. More material will be needed to cover the same area if the surface is porous or imperfect.

追加情報

追加情報

カタログコード RE-001200-H
upc code 825250025272
couleur transparent
Country of Manufacture カナダ
Manufacturer kama pigments
dimensions(Haut.,Larg.,long.) いいえ
disponible pour expédition gratuite いいえ
レビュー

商品のタグ

タグを区切るには空白を使って下さい。タグがフレーズの場合は、「'」で囲って下さい。

あなたのレビューを投稿する

Only registered users can write reviews. Please, log in or register